When your flat roof in Upwell starts to fail, the hardest decision is whether to patch it or replace it entirely - and getting that call wrong is expensive either way.
Call any time. Calls are answered day and night and passed straight to our roofers.
A leaking or deteriorating flat roof puts homeowners in an awkward position. Repairs are cheaper in the short term, but a series of patches on a roof that is past its useful life will cost more over five years than a full replacement would have done at the start. The right answer depends on the specific condition of your roof, your budget, and how long you plan to stay in the property. This page sets out the factors that point towards repair and the factors that point towards replacement - so you can have an informed conversation with any roofer you bring to the job.
Before deciding between repair and replacement, it helps to know what system is already on the roof. Most existing flat roofs fall into one of three categories: traditional built-up felt (often laid 20-40 years ago), torch-on felt (a heat-welded two or three-layer system), or EPDM rubber membrane (increasingly common on newer installations and replacements). Each ages differently and presents different repair options.
Older built-up felt becomes brittle with age. It blisters in warm weather, cracks at seams, and eventually allows water to migrate under the surface before it shows as a visible leak inside. Torch-on felt in good condition can be patched effectively where a localised failure occurs. EPDM is arguably the most repairable of the three - a clean tear or puncture can often be sealed with a compatible adhesive patch that bonds securely to the existing membrane.
A repair is the right answer when the failure is genuinely localised and the rest of the roof remains in sound condition. Signs that a repair is a reasonable option include:
A skilled roofer can cut out and relay a section of torch-on felt or apply an EPDM patch with the right primer and adhesive. Done properly, a repair to an otherwise sound roof can extend its life by several years without compromising performance.
Replacement becomes the sensible option when the problems are widespread rather than localised. A flat roof that has been patched more than twice in a few years is telling you that the underlying system has reached the end of its life. Further repairs are temporary - you are spending money to delay the inevitable.
Specific conditions that point to full replacement include:
Many homeowners focus entirely on the membrane and overlook the timber deck beneath it. The deck is the structural platform that the membrane sits on, and a new membrane laid over rotten or wet boards is a waste of money. The boards will continue to deteriorate, causing the membrane above to deform and eventually fail - often within two or three years of the new installation.
A roofer should inspect the deck before committing to either repair or replacement. If they cannot assess the deck without stripping the old surface, they should say so and factor potential deck repair into the quote. The extent of rotten decking is often only confirmed once the old felt comes off - a reputable contractor will discuss this possibility before work starts rather than presenting a surprise additional charge afterwards.
Where deck replacement is needed, the boards should typically be 18mm tongue-and-groove WBP plywood. Cheaper materials or thinner boards are a false economy on a flat roof because they deflect under load and create stress points in the membrane above.
When replacing an existing flat roof, homeowners usually choose between EPDM rubber and torch-on felt. Both are well-established systems. The choice depends on the roof size, budget, and specific conditions of the job.
EPDM is a single-ply rubber membrane that is cold-bonded to an insulation board. Its advantages are significant: it has good resistance to ultraviolet degradation, remains flexible at low temperatures, and is straightforward to repair if it is ever damaged. Manufacturers rate EPDM membrane life at 25 years or more, and the material does not harden and crack the way that older felt does. It is particularly suited to larger, unobstructed flat roof areas such as garage roofs and single-storey extension roofs.
Torch-on felt is less expensive per square metre and performs well when correctly installed. It is a proven option for straightforward jobs and is widely used across the trade. Its main vulnerability is at the seams and upstands, where poor torching leaves gaps that water eventually finds. On a well-executed installation with properly torched laps, it is a reliable system.
Flat roof repair costs vary widely depending on access and materials. Full replacement costs depend on the size of the roof, the system chosen, and whether new decking boards are needed. Torch-on felt replacement would generally come in somewhat lower than EPDM. Costs are indicative; the actual cost depends on the specific condition of the existing roof and deck.
When comparing the cost of repeated repairs against replacement, consider how many repair calls you have already had, and how old the roof is. Two repair visits at £300 each on a roof that still needs replacing within two years has cost you £600 towards a bill you will pay anyway.
Downham Market Roofers work on flat roofs in Upwell and the surrounding area. Call us to arrange a roof inspection so we can give you a straight answer on whether your flat roof needs a repair or a full replacement - before you commit to either.
No obligation · We'll call you to arrange a free visit
Call any time. Calls are answered day and night and passed straight to our roofers.