When lead flashing fails around a chimney or dormer in Upwell, knowing whether to repair or replace it is the decision that will save you money - or cost you a fortune if you get it wrong.
Call any time. Calls are answered day and night and passed straight to our roofers.
Lead flashing is the strip of dressed metal that seals the gap between your roof covering and any vertical surface rising through or against it. Chimneys, dormer windows, skylights, parapet walls, and roof valleys all rely on it. Without a sound lead seal at those junctions, rainwater tracks down the face of the brickwork or behind the tiles and into your roof structure before you ever see a drip inside.
Lead has been used on British roofs for centuries because it does things no other material matches in practice. It is soft enough to dress tightly into mortar joints and around curved profiles, it expands and contracts with temperature without cracking, and a correctly installed sheet will outlast almost any other part of the roof. The problem is not lead as a material - it is joints that were poorly cut, flashings that were never properly fixed into the masonry, or sections that have simply reached the end of a long life and need attention.
A common problem is mortar failure at the ragged joint. Lead flashing is tucked into a horizontal chase cut into the brickwork, then held with mortar or lead wedges. When that mortar breaks down - through frost, age, or poor original workmanship - the top edge of the flashing lifts. Water gets behind it rather than over it, and the wall or ceiling below starts to show damp long after the damage has started.
Another common issue is cracking and fatigue in the lead itself. Lead that has been laid too thinly, in sheets that are too long, or without the correct joints to allow movement will eventually crack along stress lines. Step flashings on chimneys are a typical place to see this: each section should be no more than around 1.5 metres long so it can move freely with thermal change. Where longer sections were fitted without lap joints, fatigue cracks open over time.
Valley gutters - the channels where two roof slopes meet - are another area where lead work is critical. A split or blocked lead valley can back water up under the tiles on both sides of the junction. On older properties this can go unnoticed for years until the roof deck itself has rotted.
Chimney stacks serving redundant fireplaces still penetrate the roof and still need sound flashing even if the fire below has not been lit in decades. An unused chimney is not a low-risk chimney.
This is the question that matters most for a homeowner facing a lead work problem. The answer depends on three things: the age and condition of the existing lead, the cause of the failure, and how much of the flashing is affected. Getting this wrong in either direction costs money - patching lead that is genuinely failing throughout simply delays the inevitable, while stripping out sound lead that could have been re-fixed wastes material and labour for no reason.
Repair makes sense when the lead itself is structurally sound and the problem is with how it has been fixed or sealed rather than with the material. The most straightforward repair is re-pointing the ragged joint. If the flashing has simply lifted because the mortar holding its top edge has crumbled, a roofer can re-wedge or re-point that joint and seal it without touching the lead below. This is a relatively modest job and, done properly, it restores the weathertight seal without the cost of new material.
Small splits or pinholes in otherwise sound lead can also be repaired using lead burning, which fuses new lead onto the existing sheet, or with lead-bonded tape as a shorter-term measure on secondary flashings. Where a section of step flashing on a chimney has cracked but the surrounding sections are sound, replacing just that section rather than the entire stack flashing is the proportionate response.
Repair is also appropriate when lead has been displaced rather than deteriorated - for example, after storm damage has lifted a section away from the wall. Provided the lead is undamaged and has not been kinked or cracked in lifting, it can often be re-dressed and refixed.
A useful rule for homeowners: if a roofer tells you a repair will last, ask them to explain why the lead is still serviceable. They should be able to point to specific evidence - the thickness of the material, the absence of fatigue cracking, the sound condition of the surrounding mortar beds. A repair recommendation should always be backed by a clear reason, not just a lower price.
Replacement becomes the correct choice when the lead itself has deteriorated to the point where it cannot hold a reliable seal. The clearest signs are multiple fatigue cracks across the surface, lead that has thinned visibly through corrosion or physical wear, or sections that have hardened and lost their ability to conform to the surface beneath. Old lead that has become brittle will not respond to re-dressing; it will simply crack further when worked.
Code 4 lead (approximately 1.8 millimetres thick) is the standard minimum for most flashing applications on domestic roofs. Code 3 was used on older properties and is thinner; where Code 3 lead has been in place for many decades, it may have thinned further through surface corrosion and is often no longer fit for purpose. Replacement with Code 4 or Code 5 (around 2.24 millimetres) brings the detail up to current standards.
Replacement is also the right call when the failure has been caused by a design fault rather than age alone. If the original flashing was laid in sections that were too long, had inadequate overlap, or was fixed to a chimney that has since moved or settled, patching the current lead without correcting the underlying issue will only produce the same failure again in a few years. A full replacement allows the detail to be redesigned and cut correctly.
Where a chimney stack is being re-pointed, rebuilt, or capped, it nearly always makes sense to replace the lead at the same time. The cost of replacing the lead separately on a second visit, after scaffolding has already been erected and the brickwork disturbed, is significantly higher than doing it as part of the same job.
Whether repair or replacement, the standard of workmanship in the installation is what determines how long the result lasts. For new or replacement flashing, the process involves cutting the lead to the correct width and length, dressing it to the profile of the surface it is sealing against, and chasing the top edge into the mortar joint at the correct depth - typically around 25 millimetres. The chase is then wedged with lead wedges and pointed with mortar or a flexible sealant appropriate for the situation.
For step flashings on chimneys, each individual piece of lead overlaps the one below it by a minimum of 75 millimetres, and each piece is tucked into a separate mortar course in the brickwork. This stepped arrangement follows the line of the tiles or slates below. Where the flashing meets the top of the chimney, a separate piece called the back gutter or soaker carries water away from the junction between the stack and the main roof slope.
Valley linings are dressed into the valley and lapped at any joins, with clips or clips and solder used on longer runs. The lead is left with sufficient movement allowance so that thermal expansion does not cause buckling or pull the edges away from the tiles.
One detail that is often skipped on cheaper jobs: the correct fixing of soakers beneath slates or plain tiles at a chimney abutment. Soakers are individual pieces of lead that sit beneath each tile course and interlace with the step flashings above. Without them, the step flashing alone cannot provide a reliably weathertight seal. If a roofer quotes for a chimney flashing job and does not mention soakers where the roof is slated or plain-tiled, it is worth asking them why.
Lead correctly specified and installed to current standards typically lasts 50 to 80 years or more before replacement becomes necessary. That longevity depends on using the right code of lead for the application, cutting sections to the correct length to allow for thermal movement, and bedding the top edge securely so it cannot lift. Lead that was installed without these considerations may fail in 15 to 20 years.
The mortar pointing that holds the flashing into the brickwork will generally need attention before the lead itself does - perhaps every 20 to 30 years depending on the exposure of the chimney and the quality of the original mortar mix. Re-pointing the ragge is a minor job compared to full replacement and is worth doing as part of routine maintenance rather than waiting until water has already started to enter.
Lead work is priced by the job rather than a flat rate per metre in most cases, because access, the complexity of the detail, and the amount of lead required all vary considerably. As a guide for homeowners:
These are typical UK ranges and will vary with the complexity of the detail and the cost of scaffolding or platform hire where that is needed. Properties with tall chimneys or steeply pitched roofs will generally sit at the higher end. Always ask for a price that distinguishes the cost of the lead work itself from the cost of access, so you understand where the money is going.
When you get a quote for lead work, it is reasonable to ask the following before agreeing to anything. First, is the roofer recommending repair or replacement, and what is their specific reason for that recommendation? A good roofer can explain what they have seen on the roof and why that points to one option rather than the other.
Second, what code of lead are they proposing to use? Code 4 is the standard minimum for most applications. If a quote is unusually low, it is worth checking whether it specifies thinner Code 3 material.
Third, for chimney work on a slated or plain-tiled roof, will soakers be included? This is a direct question that separates a properly specified job from one that has been cut to hit a price.
Fourth, is scaffolding included, or will it be quoted separately? Scaffolding can add several hundred pounds to a lead work job on a tall chimney. You need to know the total cost, not just the cost of the lead itself.
Downham Market Roofers carry out lead work across Upwell and the surrounding area. Whether you need a straightforward re-point or a full chimney flashing replacement, the process starts with a proper look at what is actually there and an honest assessment of whether repair or replacement is the right call for your situation.
If you have noticed damp on a chimney breast, a stain on a ceiling near a roof junction, or you can see from the ground that the lead around your chimney has lifted or cracked, call us to arrange a roof survey so we can give you a clear picture of what needs doing and why.
No obligation · We'll call you to arrange a free visit
Call any time. Calls are answered day and night and passed straight to our roofers.