Urgent leak or storm damage? Call 01366 312325 - answered day and nightUrgent leak? Call 01366 312325
Downham Market Roofing Specialists
01366 312325 Get a Quote →

Lead Work in Wisbech

If you've spotted a damp patch near a chimney or dormer, or noticed old flashing lifting away from the brickwork, lead work is almost certainly what your roof needs in Wisbech.

Urgent leak or storm damage?

Call any time. Calls are answered day and night and passed straight to our roofers.

Call now: 01366 312325
Lead Work · Wisbech

Expert Lead Work
in Wisbech

What Lead Work Actually Does for Your Roof

Lead flashing sits at every joint where your roof covering meets a vertical surface - chimney stacks, dormer cheeks, parapet walls, and the valleys where two roof slopes meet. These are the points where water is most likely to get in. A plain tile or slate can shed rain easily, but it cannot wrap around a corner or seal against masonry. That is what lead does, and nothing else does it as well over the long term.

A properly fitted lead flashing is cut and dressed to the profile of the surface beneath it, stepped into mortar joints in the brickwork, and lapped correctly so that driven rain has nowhere to go except down and away from the building. Done right, it should outlast the roof covering itself by a significant margin. Done badly - or patched repeatedly with mastic - it becomes a source of ongoing leaks that are expensive to trace and repair.

At Downham Market Roofers, we cut, dress, and fit lead to traditional standards. That means working with the right code of lead for the location, shaping it correctly around curves and angles, and fixing it in a way that allows for thermal movement without splitting or pulling away from the substrate.

Where Lead Work Is Needed Most

Chimney flashings are the most common source of lead-related leaks on older properties. A chimney stack has four separate faces, each requiring a different type of flashing: front apron, back gutter, stepped side flashings, and a soaker course beneath. Over decades, the mortar that holds the stepped flashings in the brick joints erodes, and the lead starts to lift. Once it lifts, water runs behind it rather than over it.

Dormer windows bring their own set of challenges. The cheeks of a dormer - the vertical sides - need lead soakers and cover flashings that lap correctly with the roof tiles. The junction between the dormer roof and the main roof slope is often where poor original workmanship shows up years later. A bodged joint that seemed watertight on installation can fail once the lead hardens and cracks in cold weather.

Valleys - the V-shaped channels where two roof slopes meet - can be lined with lead or with purpose-made valley tiles. Lead valleys tend to be used where the pitch is shallow or where appearance matters. A lead valley gutter needs adequate depth and correct fall to carry heavy rainfall clear of the roof. A blocked or undersized valley is a flooding risk every time there is a sustained downpour.

Flat roof abutments, skylights, and roof lights all rely on lead or compatible flashing materials to create a seal at their perimeter. Where a flat roof section meets a house wall, the upstand must be tall enough - typically at least 150mm - and properly dressed into a chase in the brickwork to prevent water tracking back behind it.

Typical Signs That Lead Work Has Failed

Damp patches on a ceiling directly beneath a chimney breast, or on the wall of a room containing a dormer window, are the clearest indicators. However, by the time a stain appears on a ceiling, water has often been tracking through the structure for some time. The actual point of entry may be a metre or more away from where the damp shows up inside.

From the ground, or from a ladder, look for lead that has lifted away from the brickwork, lead that has cracked or torn, mortar pointing that is missing from the stepped joints, or old repair attempts using bitumen mastic or flash tape. These temporary fixes tend to last one or two winters at best. Mastic shrinks, cracks, and loses adhesion as it ages, and once it fails it can actually trap water rather than deflect it.

Split lead in a valley is sometimes visible from an upstairs window. Look for a dark line running down the centre of the valley, or a section where tiles on either side appear stained or mossy in a localised strip. These are signs that water is sitting in the valley rather than running off cleanly.

Typical Lead Work Costs in the UK

Lead work is priced by the job rather than by area, because the complexity of the cut and the access required vary considerably. As a general guide, a full chimney re-flash - removing the old lead, repointing the step joints, and fitting new lead apron, stepped flashings, and back gutter - typically costs in the region of £500 to £1,200, depending on the size of the chimney and the height of the stack. A single-face repair or apron replacement is usually £200 to £400.

Valley re-lining depends heavily on length and on what is beneath. A straight single-valley re-line in code 4 or code 5 lead is typically £400 to £800. If the boards beneath have rotted, or if tiles need lifting and re-bedding, the cost rises accordingly. Dormer cheek flashings are generally in the £300 to £700 range for a standard dormer, again depending on height and complexity.

These are honest typical figures for UK roofing work. Any quote you receive should specify the code of lead being used, what is included in terms of scaffolding or access, and whether re-pointing of mortar joints is included or charged separately. A quote that does not mention lead code is a question worth asking.

Lead Work: What to Do While You Wait, and What Not to Do Yourself

This is where we go into real detail, because the decisions a homeowner makes in the days between spotting a problem and getting a roofer on site can either limit the damage or make it significantly worse.

Step One: Confirm Where the Water Is Getting In

Before anything else, try to confirm which part of the roof is affected. Go into the loft if it is accessible and look for daylight, wet timbers, or staining on the felt below the tiles. A torch and a dry day are all you need. Mark the position of the wet patch relative to a known feature - the chimney, a dormer, the ridge - so you can describe it clearly when you call. A roofer arriving with that information can target the problem immediately rather than spending time investigating from scratch.

If you cannot access the loft, note exactly where the damp appears on the ceiling below and how long it has been visible. Is the patch growing? Does it worsen after rain or only after heavy rain? This detail helps narrow down whether the issue is a minor flashing lift or something more significant.

Step Two: Protect What Is Below

A lead flashing failure rarely causes a sudden flood, but it can allow a slow seep that, over weeks, saturates insulation, wets joists, and eventually damages ceilings and plasterwork. If you have a visible wet patch on a ceiling, place a container beneath it and put old towels around it to catch any drips. Do not leave a saturated ceiling without some form of protection - a waterlogged plaster ceiling can come down without warning if the weight builds up enough.

Move anything of value away from the area below the leak. This includes furniture, electrical fittings, and stored items in a loft. If the leak is near a light fitting or switch, treat it as a potential electrical hazard and turn off the circuit at the consumer unit until a qualified person has confirmed it is safe.

Step Three: Cover the Area from Outside If You Can Do So Safely

If the damaged area is on a low single-storey roof and you can reach it safely from the ground or from a very short ladder without setting foot on the roof itself, a heavy-duty tarpaulin fixed over the area with battens or sandbags can reduce ingress while you wait. This is a temporary measure only, and the emphasis is on safely. Do not lean out of a window to reach a roof. Do not stand on a pitched roof without proper footwear, training, and a safety line. Falls from roofs are a leading cause of serious injury and death.

If the problem is at chimney level or on a first-floor roof slope, leave it uncovered and manage the interior instead. No temporary repair you can make from that height is worth the risk.

What Not to Do: DIY Lead Repairs

Mastic sealant, flash tape (the foil-backed adhesive strip sold in DIY stores), and roof repair sprays are temporary products sold to buy time - not to fix a lead problem. They are not substitutes for dressed lead, and they will not produce a lasting seal at a chimney or valley. Applying them to a leaking flashing often delays the proper repair, and in some cases makes the roofer's job harder because the old adhesive has to be cut away before new lead can be fitted correctly.

Lead itself should not be handled by anyone unfamiliar with working at height or with the material. Lead is heavy - code 4 lead sheet weighs around 20kg per square metre - and cutting it cleanly requires proper tools and technique. Attempting to press or reshape an existing flashing without understanding how it is fixed can cause further lifting and make the leak worse.

Re-pointing the mortar joints in a chimney is sometimes done as a separate job, and a confident homeowner with pointing experience might manage the lower courses. However, the mortar joints that hold lead step flashings are a specific type of pointing - they need to be raked out to a consistent depth, and the lead is tucked back in as part of the same operation. Pointing these joints without addressing the lead itself is only half a repair.

Do not use expanding foam to fill gaps around a flashing. It is not waterproof under sustained exposure, it traps moisture against brickwork, and it makes any subsequent proper repair considerably more difficult.

What You Can Usefully Do While Waiting

Take photographs now, from the ground, of any visible damage. If your flashing is lifting, cracked, or clearly displaced, a photograph taken before any repair work gives you a clear record. If there is a dispute later about what was there before, or if you need to make an insurance claim, dated photographs are useful evidence.

Check whether your home insurance policy covers sudden and unforeseen damage to roofing. Most standard buildings insurance policies cover sudden storm damage, but not gradual deterioration. The distinction matters: if a section of flashing was blown free in a storm, the repair may be claimable. If it has simply eroded over years, it is usually a maintenance item. Read your policy schedule and call your insurer before you authorise any repair work if you think a claim might apply.

Clear your gutters if you can do so safely from a ladder fixed at gutter level. Blocked gutters overflow, and when water sits against a fascia board or runs behind a soffit, it can be misidentified as a roof leak when it is actually a gutter overflow problem. Eliminating that possibility makes the diagnosis easier for the roofer and may save you money.

What to Tell the Roofer When You Call

The more specific you can be, the faster the job can be priced and started. Useful information includes: the type of roof (pitched tiles, flat section, or both), what the suspect area is (chimney, dormer, valley), when you first noticed the damp, whether the property has had any previous flashing repairs, and whether the chimney is in active use or capped. If you have photographs, say so - they can be sent ahead of any visit to help with planning access and materials.

If you are in Wisbech and the problem involves a chimney or dormer that requires scaffolding, it is worth asking at the quoting stage whether scaffolding is included in the price or whether it will be priced separately. On some properties, scaffolding may be shared between the roofer and the access, and the arrangements for neighbours can affect timing.

Materials: Which Code of Lead and Why It Matters

Lead sheet is graded by code, which refers to its thickness and weight. Code 3 (1.32mm thick) is the lightest grade and is generally used for soakers beneath tiles. Code 4 (1.80mm) is the standard for most flashing applications - step flashings, cover flashings, and aprons. Code 5 (2.24mm) and code 6 (2.65mm) are used in valleys and gutters where the lead needs to carry water rather than simply deflect it, and in high-exposure locations.

Using the correct code for each application is not optional - it affects how long the lead will last and how it performs under thermal stress. Lead expands and contracts significantly with temperature changes, and thinner lead in a long run is more prone to fatigue cracking. Individual sections of lead in a valley, for example, should not exceed 1.5 metres in length, with proper expansion joints between them. A valley lined in one continuous piece is a sign of poor workmanship, regardless of the code used.

Rolled lead from reputable manufacturers carries a British Standard kitemark, and you can ask to see the roll before work starts if you want to confirm what is being used. This is a reasonable question, not an unreasonable one.

How Long Should Lead Work Last?

Lead is one of the most durable roofing materials available. Properly specified and fitted lead flashings in normal residential use can last 50 to 80 years or more. The mortar pointing that holds step flashings in place typically needs attention every 20 to 30 years, but the lead itself, if not physically damaged, can last the life of the building.

What shortens lead's life is incorrect installation - sections that are too long and crack under thermal movement, lead that has not been dressed tightly enough and allows water to track underneath, and over-use of sealants that harden and pull the lead rather than allowing it to move freely. A repair done properly should not need revisiting for decades.

Serving Wisbech and the Surrounding Area

We carry out lead work across Wisbech and the surrounding area, including nearby towns and villages such as March, King's Lynn, and Downham Market, and smaller settlements nearby. If you are unsure whether we cover your location, call us and we can confirm.

For a straightforward assessment of your lead work problem, call us and describe what you can see. We can usually tell from a description and a photograph whether the job is urgent or can wait, which helps you plan accordingly.

Why choose Downham Market Roofers?

  • Free survey and itemised quote
  • Fixed price - no surprises
  • Local team

Get your free quote

No obligation · We'll call you to arrange a free visit

By submitting you agree to being contacted about your enquiry. No spam, ever.

Urgent leak or storm damage?

Call any time. Calls are answered day and night and passed straight to our roofers.

Call now: 01366 312325